Spektrum SPM18100 DX18 Uživatelský manuál Strana 29
- Strana / 47
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
29SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL
EN
Combo Mixing
Combination Mixing
is available to create
OR mixing. OR mixing
allows you to assign 2
conditions where the
mix will activate if either
condition occurs. You can
also create AND mixing where 2 conditions must occur to activate
the mix.
To program Combination Mixing:
1. Activate a mix.
2. Select Combo Sw. in the Switch Selection. The Combo screen
appears.
3. Select the desired switch and active switch position for Switch
1.The mix is Active when the switch position box is lled.
4. Select the Relation (AND, OR)
5. Select the desired switch and active switch position for Switch
2.The mix is Active when the switch position box is lled.
6. Press the BACK button to save the Combination Mix.
The Master (left side) names are inputs. For example, “Aileron”
refers to the Aileron Stick. The Slave (right side) name is the name
of the channel receiving the mix command when the Master chan-
nel moves.
Back Mixing
Back Mixing applies a
mix to all related servos
in a wing or tail type. For
example, if you select 2
AIL, 2 FLAP in the Air-
craft Type screen, a mix
to one aileron channel
affects both aileron servos.
The mix response, however, depends on the aileron channel
included in the mix.
A Back Mix also enables you to use fewer mixes to achieve the
desired response, for example adding roll to a split elevator.
1/2 Mixing Values
When adjusting the mix values near center (below 10), 1/2% mix
values are available for ne adjustment capability.
IMPORTANT: This function is only available in program mixes and
rudder to aileron/elevator in aircraft model type.
Origin Mixing
Origin Mixing uses true
stick position as the
input for a mix. When
origin mixing is selected,
any other settings to the
master channel will be
ignored and the mix will
be based strictly on stick position and trim position. When Aileron,
Elevator, or Rudder are selected as the master, origin mixing is
available. Once Aileron, Elevator, or Rudder are selected, an N will
appear next to the master channel, where N means normal. Roll
and select the N to change to O for origin mixing. Next, select the
slave channel and set the switch and mix rates as desired.
Sequencer
The Sequencer menu
option provides this-
then-that mixing with a
time delay. Five different
sequences (S1 through
S5) are available to
control 2 functions each
(A and B), in 2 timing directions (forward or reverse). Sequences
appear throughout function screens as assignable switches.
CAUTION: Always review the action of a sequence on the
Monitor or X-Plus Monitor screen BEFORE operating the
model to ensure controls act as desired. Failure to do so could
cause a crash, resulting in property damage and or injury.
You can program multiple functions to sequentially activate in
response to an assigned switch. For example, an assigned Gear
switch can open gear doors, lower the gear, then close the doors.
In reverse, gear doors open, the gear retracts and the gear doors
close.
You can assign each Sequencer function to a switch in most
Function screens such as Flight Mode, Dual Rate, Mixing, Throttle
Curve, Pitch Curve, etc.
You can assign several functions to a sequence to decrease
the number of controls you need to touch during complex ight
transitions—for example, applying your assigned dual rates and
exponential when the landing gear deploys and the ight mode
changes.
If you select an S-Number-A sequence (e.g. S3A), the sequence
operates as a timed 5-position switch. An S-Number-B sequence
operates as a timed 3-position switch. The 5 positions correspond
to the sequencer values shown on the time delay graph in the
second Sequencer screen. In a function screen, highlight each
point (0–4) and select the switch position desired for a function to
be active.
When S1B (or another sequence-number-B) is selected as a
switch in a function, the sequence will operate as a timed 3-posi-
tion switch. The 3 positions act as ‘kick points’ of the movement
at xed percentages (equal thirds) of the sequencer output. In a
function screen, highlight each point (0–2) and select the switch
position desired for a function to be active.
Sequencer Set Up
1. In the rst Sequencer screen, select 1 of the 5 available
sequences.
2. In the second
Sequencer screen,
assign a switch to
the sequence. We
recommend using a
2-position switch.
Tip: If you need to
use a 3-position switch, you must assign one direction to two
adjacent switch positions—e.g., 0 and 1. Assign the opposite
direction to the third switch position.
- Instruction Manual 1
- Bedienungsanleitung 1
- Manuel d’utilisation 1
- Manuale di Istruzioni 1
- Warranty Registration 2
- General Notes 2
- Pilot Safety 2
- Box Contents 3
- Table of Contents 4
- Transmitter Batteries 5
- Charging Your Transmitter 5
- Transmitter Functions 6
- Navigation 8
- Main Screen 8
- Mode 2 shown 9
- SmartSafe 10
- Failsafe 10
- Hold Last Command 10
- Preset Failsafe 10
- Installation 11
- X-Plus Channels and Failsafe 12
- Installing the SD Card 12
- MODEL TYPE PROGRAMMING GUIDE 13
- COMMON SYSTEM SETUP FUNCTIONS 14
- Spoken Flight Mode Setup 15
- F-Mode Setup 15
- Channel Assign 16
- Channel Input Confi guration 16
- Trim Setup 16
- X-Plus Input Confi guration 16
- Model Utilities 17
- Telemetry 18
- Warnings 18
- Frame Rate 19
- Prefl ight Setup 19
- Trainer 20
- Wireless Trainer 21
- Trainer Alerts 21
- System Settings 22
- Analog Switch Setup 22
- Extra Settings 23
- Serial Number 23
- Calibrate 23
- Transfer SD Card 24
- FUNCTION LIST 26
- D/R & Exponential 27
- Change the offset value 28
- Offset is not 28
- Sequencer 29
- Range Test 30
- Custom Voice Setup 31
- System Setup 31
- X-Plus Monitor 32
- ACRO (AIRPLANE) 33
- Elevon Servo Control 34
- Flap System 34
- ACRO Mixing 34
- Acro Gyro Function 35
- Pitch Curve Function 35
- HELI (HELICOPTER) 36
- Governor 37
- Tail Curve 37
- SAIL (SAILPLANE) 38
- SAIL Mixing 39
- Features: 40
- Receiver Installation 40
- Power System Requirements 40
- Function 41
- TROUBLESHOOTING GUIDE 42
- PARTS LIST 42
- 1-YEAR LIMITED WARRANTY 43
- FCC INFORMATION 44
- FAA INFORMATION 44
- IC INFORMATION 44
- Declaration of Conformity 46
Související produkty a manuály pro Kontrolní panel Spektrum SPM18100 DX18
(45 stránky)
(45 stránky)
(42 stránky)
(46 stránky)
Kontrolní panel Spektrum DX7 Uživatelský manuál
(108 stránky)
(108 stránky)
Philips 298X4QJAB/11 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Telewizory i monitory Philips 298X4QJAB/11.
Dostarczamy 1 pdf podręczników Philips 298X4QJAB/11 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce